Specifications for FSH

Specifications

Body
Sides, ends and side supports are of 10 ga. steel and are continuous-seam
welded from the inside. Side slope is 45º minimum with front slope at 18º and
rear slope 9º. Floor is replaceable 7 ga. steel. Longsills are 7 ga. steel
continuous-seam welded to the sides on mild steel units. Top edge of
hopper is formed "J" channel, 1-5/8" x 3/4". Feedgate is 10 ga. 10" x 18",
screwjack adjustable from curb side. Download pressure is reduced by an
adjustable inverted vee (optional) to reduce material compaction.

Conveyor
Rear discharge pintle chain conveyor is 24" wide. Chain tension adjusting
rod is 5/8" stainless steel. Idler adjustment is 4".

Conveyor Gearbox
The FSH-I and II have a 50:1 or 25:1 worm gearbox. In addition, the FSH-III
has a 6:1 spur gearbox available. All gearboxes have an extended
thru-shaft for electronic sensor mounting.

Spinner Chute Assembly
Enclosed design is contructed of 10 ga. steel. Five (5) position telescopic
adjustment; 26" - 38" below mounting surface. Two (2) baffles direct
flow of materials onto spinner. Four (4) overlapping spinner deflectors
are adjustable rod and clip pin. Spinner baffles and deflectors are
adjustable without tools.

Spinner disk is 20" diameter, 10 ga. steel with replaceable hub. Six (6)
10 ga. stainless steel vanes are bolt-on and replaceable. The spinner
hydraulic motor is mounted directly on top of the spinner disk to
eliminate shaft and bearings.

Paint
All metal surfaces are high pressure cleaned with a phosphate solution
to remove slag, spatter, oxide and oil residue. The entire body is
primed with a high quality catalyzed primer and then finished with
Highway Orange industrial grade enamel. The 304 Stainless Steel
units are unpainted.

Control Valve - Optional
Speed of conveyor and spinner motors is controlled by a dual pressure
compensated control valve with a relief pre-set at 1500PSI. Valve
has twelve (12) detent settings for each circuit and an independent
on/off valve to allow start/stop without changing application rate.

Length	Cubic Yard Capacity (Struck/Rounded)			Weights (Approx.)			Recommended Cab to Axle (inches)
	Side Height			Side Height
	48" or 50"	54" or 56"	60" or 62"	50"	56"	62"
8'	4.5/5.6	5.5/5.6	6.5/7.6	1760	1845	1930	60
9'	5.1/6.3	6.2/7.3	7.4/8.5	1905	1995	2085	72
10'	5.6/6.9	6.9/8.2	8.3/9.6	2070	2166	2262	84
11'	6.2/7.6	7.6/9.0	9.0/10.4	2225	2327	2429	96
12'	6.8/8.3	8.4/8.9	9.9/11.4	2380	2488	2596	108
13'	7.3/9.0	9.0/10.7	10.7/12.4	2535	2649	2763	96 C.T.
14'	7.9/9.8	9.7/11.4	11.6/13.3	2690	2810	2930	108 C.T.
15'	8.4/10.3	10.3/12.2	12.2/14.1	2845	2971	3097	120 C.T.
16'	8.9/10.9	11.0/13.0	13.0/15.0	3001	3132	3264	132 C.T.